Add two physical buttons: factory-reset and next-photo

Factory-reset (GPIO3, hold 10s): clears stored WiFi/server config and
restarts into provisioning -- the deliberate, USB-free replacement for
the earlier reverted RST-based auto-reprovisioning idea.

Next-photo (GPIO2, tap): wakes the device and forces the server to
advance immediately via a new POST /frame/advance, instead of waiting
for the refresh interval. Both buttons arm themselves as deep-sleep GPIO
wakeup sources so a press is noticed promptly even while asleep.

Also makes GET /frame/image side-effect-free: it now only advances once
refresh_interval_s has elapsed since the current photo was set (tracked
server-side), so a device reboot for any reason just redisplays the
current photo instead of silently skipping ahead. The server maintains a
small reorderable upcoming-photos queue, viewable and rearrangeable from
the web UI.

docs/hardware.md

@@ -28,6 +28,22 @@ Configuration** if your wiring differs.
 | VCC       | 3.3V          | --                 |
 | GND       | GND           | --                 |
 
+Optionally, two buttons, both wired the same way -- momentary push button
+between the GPIO and GND, no external resistor needed (the firmware
+enables each pin's internal pull-up, so it idles high and reads low when
+pressed):
+
+- **Factory-reset (GPIO3)**: held for 10 seconds, clears the stored
+  WiFi/server config; see
+  [`firmware/README.md`](../firmware/README.md#resetting-to-provisioning-mode).
+- **Next photo (GPIO2)**: a normal press skips immediately to the next
+  photo; see
+  [`firmware/README.md`](../firmware/README.md#skipping-to-the-next-photo).
+
+Both pins were picked because they're within GPIO 0-7 -- the only pins
+the ESP32-C6 can wake from deep sleep on -- aren't strapping pins, and
+aren't already used by the panel wiring above.
+
 A couple of things worth knowing if you pick different pins:
 
 - **Avoid the ESP32-C6's strapping pins** (GPIO 4, 5, 8, 9, 15) and the

firmware/README.md

@@ -44,6 +44,9 @@ Under **ESPresso Frame Configuration**:
 | `FRAME_FETCH_TIMEOUT_MS` | 15000 | Timeout for `GET /frame/image` |
 | `FRAME_SLEEP_INTERVAL_S` | 3600 | **Fallback only** -- the refresh interval is normally set server-side; see below |
 | `FRAME_RETRY_INTERVAL_S` | 300 | Sleep duration after a failed cycle, before retrying |
+| `FRAME_RESET_BUTTON_GPIO` | 3 | Factory-reset button GPIO (-1 to disable). Must be 0-7 (ESP32-C6's deep-sleep-wakeup-capable pins) |
+| `FRAME_RESET_BUTTON_HOLD_MS` | 10000 | How long the button must be held to trigger a reset |
+| `FRAME_NEXT_BUTTON_GPIO` | 2 | Next-photo button GPIO (-1 to disable). Must be 0-7 |
 
 Under **E-Paper Display (epd7in3e) Configuration**: SPI/GPIO pin
 assignments and SPI clock speed -- see
@@ -77,11 +80,35 @@ Server" address (`host:port` of the [server](../server/) -- **not** your
 Immich server). Saving reboots the device, which then connects to your
 home network and starts its normal fetch/sleep cycle.
 
+## Skipping to the next photo
+
+Wire a momentary push button between GPIO2 and GND (internal pull-up,
+active-low, same wiring style as the reset button). A press wakes the
+device (if asleep) and tells the server to advance to the next photo
+right away, regardless of the configured refresh interval -- no long hold
+needed, unlike the factory-reset button, since advancing is easily
+reversible by pressing again. See `FRAME_NEXT_BUTTON_GPIO` above to
+change the pin or disable the feature.
+
+Normal wakes and reboots never advance the photo on their own -- the
+server decides when to advance based on its own clock (see
+[`server/README.md`](../server/README.md)), so an unplanned reboot just
+redisplays whatever was already showing instead of skipping ahead.
+
 ## Resetting to provisioning mode
 
-There's currently no in-field way to force the device back into
+Wire a momentary push button between GPIO3 and GND (internal pull-up,
-provisioning (a future addition) -- reconfiguring means erasing its NVS
+active-low -- no external resistor needed). Hold it for 10 seconds (from
-partition over USB:
+either power-on or while the device is deep-asleep -- GPIO3 is armed as a
+wakeup source) and it clears the stored WiFi/server config and restarts
+into provisioning. Releasing it early is a no-op; nothing happens until
+the full hold duration elapses, so a brief accidental bump won't
+reprovision the device. See `FRAME_RESET_BUTTON_GPIO`/
+`FRAME_RESET_BUTTON_HOLD_MS` above to change the pin or hold duration, or
+disable the feature.
+
+Without the button wired up (or with `FRAME_RESET_BUTTON_GPIO` set to
+`-1`), reconfiguring still works by erasing the NVS partition over USB:
 
 ```
 python -m esptool --chip esp32c6 -p PORT erase-region 0x9000 0x6000

firmware/main/CMakeLists.txt

@@ -1,3 +1,3 @@
-idf_component_register(SRCS main.c wifi_provisioning.c frame_client.c qr_onboarding.c status_screen.c epd_draw.c
+idf_component_register(SRCS main.c wifi_provisioning.c frame_client.c qr_onboarding.c status_screen.c epd_draw.c reset_button.c next_button.c
-                       PRIV_REQUIRES esp_event nvs_flash esp_wifi esp_netif esp_http_server esp_http_client dns_server epd7in3e qrcode epaper_fonts
+                       PRIV_REQUIRES esp_event nvs_flash esp_wifi esp_netif esp_http_server esp_http_client dns_server epd7in3e qrcode epaper_fonts esp_driver_gpio
                        EMBED_FILES root.html)

firmware/main/Kconfig.projbuild

@@ -83,4 +83,42 @@ menu "ESPresso Frame Configuration"
             server was unreachable or the fetch/display failed, instead of
             waiting the full FRAME_SLEEP_INTERVAL_S.
 
+    config FRAME_RESET_BUTTON_GPIO
+        int "Factory-reset button GPIO (-1 to disable)"
+        default 3
+        range -1 7
+        help
+            Button wired between this GPIO and GND (active-low, internal
+            pull-up enabled in firmware -- no external resistor needed).
+            Holding it for FRAME_RESET_BUTTON_HOLD_MS clears the stored
+            WiFi/server config and restarts the device into provisioning
+            mode. Must be GPIO 0-7 -- the only pins the ESP32-C6 can use as
+            an EXT1 deep-sleep wakeup source, which is what lets a press
+            wake the device promptly instead of only being noticed during
+            its brief awake windows. Set to -1 to disable the feature
+            entirely.
+
+    config FRAME_RESET_BUTTON_HOLD_MS
+        int "Factory-reset button hold duration (ms)"
+        default 10000
+        depends on FRAME_RESET_BUTTON_GPIO >= 0
+        help
+            How long the reset button must be held continuously before the
+            device clears its stored config and reboots into provisioning.
+            Long enough that it won't trigger by accident.
+
+    config FRAME_NEXT_BUTTON_GPIO
+        int "Next-photo button GPIO (-1 to disable)"
+        default 2
+        range -1 7
+        help
+            Button wired between this GPIO and GND (active-low, internal
+            pull-up enabled in firmware -- no external resistor needed).
+            Pressing it wakes the device (if asleep), forces the server to
+            advance to the next photo immediately (POST /frame/advance)
+            regardless of the configured refresh interval, and displays
+            it. Must be GPIO 0-7 for the same deep-sleep-wakeup reason as
+            FRAME_RESET_BUTTON_GPIO above; defaults to a different pin
+            than the reset button. Set to -1 to disable the feature.
+
 endmenu

firmware/main/frame_client.c

@@ -212,19 +212,20 @@ static size_t http_read_fn(uint8_t *chunk, size_t chunk_size, void *ctx_)
     return n > 0 ? (size_t)n : 0;
 }
 
-/* GETs /frame/image and streams the response directly into the panel.
+/* GETs /frame/image (or, if force_advance, POSTs /frame/advance to skip
+ * ahead immediately) and streams the response directly into the panel.
  * Returning non-ESP_OK means the panel was never actually refreshed --
  * epd_display_stream() (see epd7in3e.c) refuses to trigger a physical
  * refresh on a short/wrong-size stream, so a failure here always leaves
  * the visible screen exactly as it was. */
-static esp_err_t fetch_and_display(const frame_config_t *cfg)
+static esp_err_t fetch_and_display(const frame_config_t *cfg, bool force_advance)
 {
     char url[160];
-    snprintf(url, sizeof(url), "http://%s/frame/image", cfg->toolsserver);
+    snprintf(url, sizeof(url), "http://%s/%s", cfg->toolsserver, force_advance ? "frame/advance" : "frame/image");
 
     esp_http_client_config_t config = {
         .url = url,
-        .method = HTTP_METHOD_GET,
+        .method = force_advance ? HTTP_METHOD_POST : HTTP_METHOD_GET,
         .timeout_ms = CONFIG_FRAME_FETCH_TIMEOUT_MS,
     };
     esp_http_client_handle_t client = esp_http_client_init(&config);
@@ -255,7 +256,7 @@ static esp_err_t fetch_and_display(const frame_config_t *cfg)
     return err;
 }
 
-void frame_client_run(const frame_config_t *cfg)
+void frame_client_run(const frame_config_t *cfg, bool force_advance)
 {
     esp_err_t epd_err = epd_init();
     bool have_display = (epd_err == ESP_OK);
@@ -292,7 +293,7 @@ void frame_client_run(const frame_config_t *cfg)
             status_screen_show(cfg->sta_ssid, STATUS_OK, cfg->toolsserver, STATUS_OK);
         }
         if (have_display) {
-            esp_err_t fetch_err = fetch_and_display(cfg);
+            esp_err_t fetch_err = fetch_and_display(cfg, force_advance);
             if (fetch_err != ESP_OK) {
                 /* epd_display_stream() never triggers a physical refresh on
                  * a failed/short/wrong-size stream (see epd7in3e.c), so the

firmware/main/frame_client.h

@@ -1,5 +1,7 @@
 #pragma once
 
+#include <stdbool.h>
+
 #include "esp_err.h"
 #include "wifi_provisioning.h"
 
@@ -15,8 +17,11 @@ esp_err_t frame_wifi_connect_sta(const frame_config_t *cfg);
  * Runs the frame's normal-operation cycle: fetch the current image from
  * cfg->toolsserver, display it, and deep-sleep until the next refresh.
  *
- * TODO(step 6): implement the HTTP fetch + EPD display + esp_deep_sleep
+ * If force_advance is true (the next-photo button was held), the fetch
- * cycle once the display driver (step 4) and server (step 3) exist. For
+ * forces the server to skip ahead to the next photo immediately
- * now this just confirms STA connectivity survives a reboot.
+ * (POST /frame/advance) instead of the normal idempotent GET /frame/image
+ * -- the server decides on its own whether to advance in the normal case,
+ * based on its configured refresh interval, so a plain wake/reboot never
+ * skips a photo just by asking.
  */
-void frame_client_run(const frame_config_t *cfg);
+void frame_client_run(const frame_config_t *cfg, bool force_advance);

firmware/main/main.c

@@ -1,3 +1,5 @@
+#include <stdbool.h>
+
 #include "esp_event.h"
 #include "esp_log.h"
 #include "nvs_flash.h"
@@ -5,6 +7,8 @@
 
 #include "wifi_provisioning.h"
 #include "frame_client.h"
+#include "reset_button.h"
+#include "next_button.h"
 
 static const char *TAG = "main";
 
@@ -26,12 +30,23 @@ void app_main(void)
     }
     ESP_ERROR_CHECK(nvs_err);
 
+    /* Arms both buttons as deep-sleep wakeup sources (so holding one wakes
+     * the device promptly, not just during its brief awake windows), then
+     * checks them -- covers both "held while asleep, just woke us up" and
+     * "held while powering on" the same way, since both look identical
+     * from here: the pin is just low right now. */
+    reset_button_init();
+    next_button_init();
+    reset_button_check(); /* clears config + restarts if held the full duration; never returns in that case */
+
+    bool force_advance = next_button_check();
+
     frame_config_t cfg;
     esp_err_t cfg_err = frame_config_load(&cfg);
     if (cfg_err == ESP_OK) {
         ESP_LOGI(TAG, "Found stored config for '%s', connecting to home WiFi", cfg.sta_ssid);
         if (frame_wifi_connect_sta(&cfg) == ESP_OK) {
-            frame_client_run(&cfg);
+            frame_client_run(&cfg, force_advance);
             return; /* frame_client_run currently never returns */
         }
         ESP_LOGW(TAG, "Could not connect to stored WiFi after %d attempts, falling back to provisioning",

firmware/main/next_button.c

@@ -0,0 +1,69 @@
+#include "driver/gpio.h"
+#include "esp_log.h"
+#include "esp_sleep.h"
+
+#include "freertos/FreeRTOS.h"
+#include "freertos/task.h"
+
+#include "next_button.h"
+
+static const char *TAG = "next_button";
+
+#if CONFIG_FRAME_NEXT_BUTTON_GPIO >= 0
+
+#define NEXT_BUTTON_GPIO ((gpio_num_t)CONFIG_FRAME_NEXT_BUTTON_GPIO)
+#define NEXT_BUTTON_DEBOUNCE_MS 20
+#define NEXT_BUTTON_DEBOUNCE_CHECKS 3
+
+void next_button_init(void)
+{
+    gpio_config_t io_conf = {
+        .pin_bit_mask = 1ULL << NEXT_BUTTON_GPIO,
+        .mode = GPIO_MODE_INPUT,
+        .pull_up_en = GPIO_PULLUP_ENABLE,
+    };
+    gpio_config(&io_conf);
+
+    /* See reset_button.c for why this API (not ext1) -- it manages the
+     * pull resistor across the sleep transition itself, so the pin
+     * doesn't float and wake the device spuriously. */
+    esp_sleep_enable_gpio_wakeup_on_hp_periph_powerdown(1ULL << NEXT_BUTTON_GPIO, ESP_GPIO_WAKEUP_GPIO_LOW);
+}
+
+bool next_button_check(void)
+{
+    /* A quick tap can easily release before this runs (~0.4-0.5s into
+     * boot, confirmed on hardware -- a live gpio_get_level() check here
+     * missed real presses that had already woken the device). The wakeup
+     * status register is latched at the moment of waking and isn't
+     * cleared until the next sleep entry, so it reliably reflects a tap
+     * regardless of how quickly it was released. */
+    if (esp_sleep_get_gpio_wakeup_status() & (1ULL << NEXT_BUTTON_GPIO)) {
+        ESP_LOGI(TAG, "Next-photo button caused this wake, forcing advance");
+        return true;
+    }
+
+    /* Not a GPIO-wakeup-from-this-pin boot (normal timer wake, or a fresh
+     * power-on/reflash) -- fall back to a live, debounced level check so
+     * holding the button down while powering on also works. */
+    if (gpio_get_level(NEXT_BUTTON_GPIO) != 0) {
+        return false;
+    }
+
+    for (int i = 0; i < NEXT_BUTTON_DEBOUNCE_CHECKS; i++) {
+        vTaskDelay(pdMS_TO_TICKS(NEXT_BUTTON_DEBOUNCE_MS));
+        if (gpio_get_level(NEXT_BUTTON_GPIO) != 0) {
+            return false; /* noise, not a real press */
+        }
+    }
+
+    ESP_LOGI(TAG, "Next-photo button held during power-on, forcing advance");
+    return true;
+}
+
+#else
+
+void next_button_init(void) {}
+bool next_button_check(void) { return false; }
+
+#endif

firmware/main/next_button.h

@@ -0,0 +1,21 @@
+#pragma once
+
+#include <stdbool.h>
+
+/**
+ * Configures the next-photo button GPIO (CONFIG_FRAME_NEXT_BUTTON_GPIO,
+ * active-low with internal pull-up) and arms it as a deep-sleep wakeup
+ * source, same as reset_button_init(). Call once, early in app_main(),
+ * before the device might enter deep sleep.
+ *
+ * A no-op if CONFIG_FRAME_NEXT_BUTTON_GPIO is negative (button disabled).
+ */
+void next_button_init(void);
+
+/**
+ * Returns whether the next-photo button is currently held, debounced with
+ * a couple of short re-checks to reject noise. Unlike the reset button,
+ * there's no long hold-to-confirm gate -- advancing a photo is low-stakes
+ * and should feel immediate, so this returns right away either way.
+ */
+bool next_button_check(void);

firmware/main/reset_button.c

@@ -0,0 +1,68 @@
+#include "driver/gpio.h"
+#include "esp_log.h"
+#include "esp_sleep.h"
+
+#include "freertos/FreeRTOS.h"
+#include "freertos/task.h"
+
+#include "wifi_provisioning.h"
+
+#include "reset_button.h"
+
+static const char *TAG = "reset_button";
+
+#if CONFIG_FRAME_RESET_BUTTON_GPIO >= 0
+
+#define RESET_BUTTON_GPIO ((gpio_num_t)CONFIG_FRAME_RESET_BUTTON_GPIO)
+#define RESET_BUTTON_POLL_MS 100
+
+void reset_button_init(void)
+{
+    gpio_config_t io_conf = {
+        .pin_bit_mask = 1ULL << RESET_BUTTON_GPIO,
+        .mode = GPIO_MODE_INPUT,
+        .pull_up_en = GPIO_PULLUP_ENABLE,
+    };
+    gpio_config(&io_conf);
+
+    /* Not esp_sleep_enable_ext1_wakeup_io(): its internal pull resistors
+     * don't hold once the RTC_PERIPH domain powers down for deep sleep, so
+     * the pin floats and reads spuriously low, waking the device instantly
+     * on every sleep entry (confirmed on hardware -- boot-looped every
+     * ~27s, the length of one fetch/display cycle, instead of sleeping for
+     * the configured interval). This GPIO-wakeup variant manages the pull
+     * resistor itself across the sleep transition. */
+    esp_sleep_enable_gpio_wakeup_on_hp_periph_powerdown(1ULL << RESET_BUTTON_GPIO, ESP_GPIO_WAKEUP_GPIO_LOW);
+}
+
+void reset_button_check(void)
+{
+    if (gpio_get_level(RESET_BUTTON_GPIO) != 0) {
+        return; /* not pressed */
+    }
+
+    ESP_LOGI(TAG, "Reset button held -- hold for %dms to clear config and reprovision",
+             CONFIG_FRAME_RESET_BUTTON_HOLD_MS);
+
+    int elapsed_ms = 0;
+    while (elapsed_ms < CONFIG_FRAME_RESET_BUTTON_HOLD_MS) {
+        vTaskDelay(pdMS_TO_TICKS(RESET_BUTTON_POLL_MS));
+        elapsed_ms += RESET_BUTTON_POLL_MS;
+        if (gpio_get_level(RESET_BUTTON_GPIO) != 0) {
+            ESP_LOGI(TAG, "Reset button released early, continuing normal boot");
+            return;
+        }
+    }
+
+    ESP_LOGW(TAG, "Reset button held for %dms, clearing config and restarting into provisioning",
+             CONFIG_FRAME_RESET_BUTTON_HOLD_MS);
+    frame_config_clear();
+    esp_restart();
+}
+
+#else
+
+void reset_button_init(void) {}
+void reset_button_check(void) {}
+
+#endif

firmware/main/reset_button.h

@@ -0,0 +1,22 @@
+#pragma once
+
+/**
+ * Configures the factory-reset button GPIO (CONFIG_FRAME_RESET_BUTTON_GPIO,
+ * active-low with internal pull-up) and arms it as a deep-sleep wakeup
+ * source, so holding it wakes the device promptly even while it's asleep
+ * rather than only being noticed during its brief awake windows. Call once,
+ * early in app_main(), before the device might enter deep sleep.
+ *
+ * A no-op if CONFIG_FRAME_RESET_BUTTON_GPIO is negative (button disabled).
+ */
+void reset_button_init(void);
+
+/**
+ * Checks whether the reset button is currently held. If it's held
+ * continuously for CONFIG_FRAME_RESET_BUTTON_HOLD_MS, clears the stored
+ * WiFi/server config and restarts (does not return in that case) so the
+ * device comes back up in provisioning mode. Returns immediately if the
+ * button isn't pressed, or as soon as it's released before the hold
+ * duration elapses -- normal boot continues either way.
+ */
+void reset_button_check(void);

firmware/main/wifi_provisioning.c

@@ -130,6 +130,20 @@ void frame_config_mark_connected_once(void)
     nvs_close(handle);
 }
 
+void frame_config_clear(void)
+{
+    nvs_handle_t handle;
+    if (nvs_open(NVS_NAMESPACE, NVS_READWRITE, &handle) != ESP_OK) {
+        return;
+    }
+    nvs_erase_key(handle, "sta_ssid");
+    nvs_erase_key(handle, "sta_pass");
+    nvs_erase_key(handle, "toolsserver");
+    nvs_erase_key(handle, "connected_once");
+    nvs_commit(handle);
+    nvs_close(handle);
+}
+
 static void generate_ap_password(char *out, size_t out_size)
 {
     size_t len = MIN(FRAME_AP_PASSWORD_LEN, out_size - 1);

firmware/main/wifi_provisioning.h

@@ -36,6 +36,15 @@ bool frame_config_has_connected_once(void);
 /** Marks the status screen as having been shown for the current WiFi config. */
 void frame_config_mark_connected_once(void);
 
+/**
+ * Erases the stored home-network config (SSID/password/tools server) so the
+ * device falls back into provisioning on its next boot. Leaves the softAP
+ * identity (SSID/password) untouched, since that's tied to the device
+ * itself, not a particular home network -- regenerating it on every reset
+ * would force re-scanning the join QR code for no reason.
+ */
+void frame_config_clear(void);
+
 /**
  * Returns this device's provisioning AP identity: a fixed SSID (from
  * Kconfig) and a password that's generated once on first use and persisted

server/README.md

@@ -31,25 +31,47 @@ algorithm itself -- it just streams the response straight to the panel.
 ## Endpoints
 
 - `GET /` -- config UI (album, order, refresh interval, face-aware crop
-  toggle -- not Immich URL/API key, see Setup above)
+  toggle, now-displaying + reorderable upcoming photos -- not Immich
+  URL/API key, see Setup above)
 - `GET /api/albums` -- lists Immich albums (used by the config UI)
 - `POST /api/config` -- saves album/order/refresh_interval_s/smart_crop_faces
 - `GET /frame/image` -- returns the current photo pre-processed into the
   panel's raw 800x480, 4-bit-per-pixel, 2-pixels-per-byte format
-  (`application/octet-stream`, exactly 192,000 bytes)
+  (`application/octet-stream`, exactly 192,000 bytes). **Side-effect-free**
+  by default: it only actually advances to the next photo once
+  `refresh_interval_s` has elapsed since the current one was set, so
+  calling it repeatedly (e.g. the device rebooting unexpectedly) just
+  redisplays the same photo instead of skipping ahead.
+- `POST /frame/advance` -- forces an immediate advance to the next photo,
+  ignoring `refresh_interval_s`, and resets the interval clock from now.
+  Same response shape as `/frame/image`. Used by the device's next-photo
+  button (see `firmware/README.md`).
 - `GET /frame/config` -- `{"refresh_interval_s": ...}`, polled by the frame
   each wake alongside its reachability check
+- `GET /api/queue` -- `{"current": {...} | null, "upcoming": [...]}`, each
+  entry an asset id + thumbnail URL; used by the config UI
+- `POST /api/queue/reorder` -- reorders the upcoming queue; body is
+  `{"queue": [asset_id, ...]}`, must be exactly a permutation of the
+  current queue
+- `GET /api/photo-thumbnail/{asset_id}` -- proxies an Immich thumbnail so
+  the browser never needs the Immich API key directly
 - `GET /health` -- liveness check
 
 ## Notes
 
-- Album/order/refresh-interval/etc. are stored in `./data/config.json` on
+- Album/order/refresh-interval/current photo/upcoming queue/etc. are
-  the host via the compose volume mount. Immich URL/API key are too if set
+  stored in `./data/config.json` on the host via the compose volume
-  via the web UI, but `IMMICH_URL`/`IMMICH_API_KEY` env vars (see Setup
+  mount. Immich URL/API key are too if set via the web UI, but
-  above) always take precedence when present.
+  `IMMICH_URL`/`IMMICH_API_KEY` env vars (see Setup above) always take
-- `/frame/image` isn't authenticated yet. That's fine on a trusted home
+  precedence when present.
-  LAN for now, but worth revisiting once the ESP32 side is wired up to
+- The upcoming queue is a bounded lookahead (10 photos), not the whole
-  send a shared device token.
+  album -- it's topped up automatically as photos are consumed
+  (`app/photo_queue.py`), in sequential or shuffle order per the Order
+  setting. Reordering only rearranges those 10; it doesn't add or remove
+  photos from the album.
+- `/frame/image` and `/frame/advance` aren't authenticated yet. That's
+  fine on a trusted home LAN for now, but worth revisiting once the ESP32
+  side is wired up to send a shared device token.
 - The 6-color palette RGB values in `app/image_pipeline.py` are
   approximations, not measured values (Waveshare doesn't publish exact
   color primaries for this panel) -- tune them once you can compare a

server/app/config.py

@@ -20,10 +20,17 @@ class FrameConfig(BaseModel):
     immich_api_key: str = ""
     album_id: str = ""
     order: str = "sequential"  # or "shuffle"
-    cursor: int = 0
     refresh_interval_s: int = 3600
     smart_crop_faces: bool = True
 
+    # Current photo + upcoming queue (see app/photo_queue.py). current_asset_set_at
+    # is what lets the server decide "has it been long enough to advance" on its
+    # own clock, independent of how/why the device asked for a photo.
+    current_asset_id: str = ""
+    current_asset_set_at: float = 0.0
+    queue: list[str] = []
+    queue_cursor: int = 0  # internal bookkeeping for sequential queue top-up; not user-facing
+
 
 def load() -> FrameConfig:
     with _lock:

server/app/immich_client.py

@@ -55,3 +55,17 @@ class ImmichClient:
         )
         resp.raise_for_status()
         return resp.content
+
+    def download_asset_thumbnail(self, asset_id: str) -> tuple[bytes, str]:
+        """Smaller than download_asset_preview -- used for the web UI's
+        upcoming-photos list, not the actual rendered frame. Returns
+        (content, content_type) since this one gets proxied straight to a
+        browser <img> tag and needs a correct Content-Type header."""
+        resp = httpx.get(
+            f"{self.base_url}/api/assets/{asset_id}/thumbnail",
+            params={"size": "thumbnail"},
+            headers=self._headers,
+            timeout=30,
+        )
+        resp.raise_for_status()
+        return resp.content, resp.headers.get("content-type", "image/jpeg")

server/app/main.py

@@ -5,15 +5,15 @@ from __future__ import annotations
 
 import io
 import logging
-import random
 
 import httpx
-from fastapi import FastAPI, Form, HTTPException, Request
+from fastapi import FastAPI, HTTPException, Form, Request
 from fastapi.responses import HTMLResponse, Response
 from fastapi.templating import Jinja2Templates
 from PIL import Image
+from pydantic import BaseModel
 
-from . import config
+from . import config, photo_queue
 from .image_pipeline import render_frame
 from .immich_client import ImmichClient
 
@@ -72,7 +72,12 @@ def api_config_save(
     # so there's nothing here that could overwrite or clear them.
     cfg = config.load()
     if album_id != cfg.album_id:
-        cfg.cursor = 0  # restart from the top of a newly selected album
+        # A newly selected album starts clean -- the old current photo and
+        # queue don't mean anything in the new album's context.
+        cfg.current_asset_id = ""
+        cfg.current_asset_set_at = 0.0
+        cfg.queue = []
+        cfg.queue_cursor = 0
     cfg.album_id = album_id
     cfg.order = order if order in ("sequential", "shuffle") else "sequential"
     cfg.refresh_interval_s = max(MIN_REFRESH_INTERVAL_S, min(MAX_REFRESH_INTERVAL_S, refresh_interval_s))
@@ -81,46 +86,119 @@ def api_config_save(
     return {"status": "saved"}
 
 
-@app.get("/frame/image")
+def _require_configured(cfg: config.FrameConfig) -> None:
-def frame_image():
-    cfg = config.load()
     if not cfg.immich_url or not cfg.immich_api_key:
         raise HTTPException(400, "Immich URL/API key not configured yet")
     if not cfg.album_id:
         raise HTTPException(400, "No album configured yet")
 
-    client = ImmichClient(cfg.immich_url, cfg.immich_api_key)
+
+def _list_assets(client: ImmichClient, cfg: config.FrameConfig) -> list[dict]:
     try:
         assets = client.list_album_assets(cfg.album_id)
     except httpx.HTTPError as e:
         raise HTTPException(502, f"Could not reach Immich at {cfg.immich_url}: {e}") from e
-
     if not assets:
         raise HTTPException(404, "Album has no photos")
+    return assets
 
-    if cfg.order == "shuffle":
-        asset = random.choice(assets)
-    else:
-        index = cfg.cursor % len(assets)
-        asset = assets[index]
-        cfg.cursor = (index + 1) % len(assets)
-        config.save(cfg)
 
+def _render_asset(client: ImmichClient, cfg: config.FrameConfig, asset_id: str) -> bytes:
     try:
-        jpeg_bytes = client.download_asset_preview(asset["id"])
+        jpeg_bytes = client.download_asset_preview(asset_id)
     except httpx.HTTPError as e:
         raise HTTPException(502, f"Could not download asset from Immich: {e}") from e
 
     faces = None
     if cfg.smart_crop_faces:
         try:
-            faces = client.get_asset_faces(asset["id"])
+            faces = client.get_asset_faces(asset_id)
         except httpx.HTTPError as e:
             # A faces lookup hiccup shouldn't block showing a photo at
             # all -- just fall back to a plain center-crop this cycle.
-            logger.warning("Could not fetch faces for asset %s: %s", asset["id"], e)
+            logger.warning("Could not fetch faces for asset %s: %s", asset_id, e)
 
     source = Image.open(io.BytesIO(jpeg_bytes))
-    frame_bytes = render_frame(source, faces=faces)
+    return render_frame(source, faces=faces)
 
-    return Response(content=frame_bytes, media_type="application/octet-stream")
+
+@app.get("/frame/image")
+def frame_image():
+    """Returns the current photo. Idempotent: only actually advances to
+    the next photo once refresh_interval_s has elapsed since the current
+    one was set (see app/photo_queue.py) -- safe to call as often as the
+    device wants, including after an unplanned reboot, without skipping
+    ahead in the album."""
+    cfg = config.load()
+    _require_configured(cfg)
+
+    client = ImmichClient(cfg.immich_url, cfg.immich_api_key)
+    assets = _list_assets(client, cfg)
+
+    if photo_queue.get_current(cfg, assets):
+        config.save(cfg)
+
+    return Response(content=_render_asset(client, cfg, cfg.current_asset_id), media_type="application/octet-stream")
+
+
+@app.post("/frame/advance")
+def frame_advance():
+    """Forces an immediate advance to the next photo, ignoring
+    refresh_interval_s, and resets the interval clock from now. Used by
+    the device's next-photo button."""
+    cfg = config.load()
+    _require_configured(cfg)
+
+    client = ImmichClient(cfg.immich_url, cfg.immich_api_key)
+    assets = _list_assets(client, cfg)
+
+    photo_queue.advance_forced(cfg, assets)
+    config.save(cfg)
+
+    return Response(content=_render_asset(client, cfg, cfg.current_asset_id), media_type="application/octet-stream")
+
+
+@app.get("/api/queue")
+def api_queue():
+    cfg = config.load()
+    _require_configured(cfg)
+
+    client = ImmichClient(cfg.immich_url, cfg.immich_api_key)
+    assets = _list_assets(client, cfg)
+
+    if photo_queue.get_current(cfg, assets):
+        config.save(cfg)
+
+    def entry(asset_id: str) -> dict:
+        return {"id": asset_id, "thumbnail_url": f"/api/photo-thumbnail/{asset_id}"}
+
+    return {
+        "current": entry(cfg.current_asset_id) if cfg.current_asset_id else None,
+        "upcoming": [entry(asset_id) for asset_id in cfg.queue],
+    }
+
+
+class QueueReorderRequest(BaseModel):
+    queue: list[str]
+
+
+@app.post("/api/queue/reorder")
+def api_queue_reorder(body: QueueReorderRequest):
+    cfg = config.load()
+    if set(body.queue) != set(cfg.queue) or len(body.queue) != len(cfg.queue):
+        raise HTTPException(400, "Reordered queue must contain exactly the current queue's photos")
+    cfg.queue = body.queue
+    config.save(cfg)
+    return {"status": "saved"}
+
+
+@app.get("/api/photo-thumbnail/{asset_id}")
+def api_photo_thumbnail(asset_id: str):
+    cfg = config.load()
+    _require_configured(cfg)
+    client = ImmichClient(cfg.immich_url, cfg.immich_api_key)
+    try:
+        content, content_type = client.download_asset_thumbnail(asset_id)
+    except httpx.HTTPError as e:
+        raise HTTPException(502, f"Could not download thumbnail from Immich: {e}") from e
+    return Response(content=content, media_type=content_type)

server/app/photo_queue.py

@@ -0,0 +1,100 @@
+"""Tracks which photo is currently displayed and what's queued up next.
+
+`current_asset_id` only ever changes two ways: the configured refresh
+interval elapsing (`get_current`, called on every `GET /frame/image` --
+a no-op otherwise, so an unplanned device reboot just redisplays the same
+photo instead of silently skipping ahead) or an explicit forced advance
+(`advance_forced`, called from `POST /frame/advance` -- the next-photo
+button -- ignoring elapsed time).
+
+`queue` is a small reorderable lookahead the web UI can preview and
+rearrange, topped up automatically from the album as it's consumed.
+`queue_cursor` is separate, internal-only bookkeeping for where sequential
+top-up resumes in the album -- not shown or reordered in the UI.
+"""
+
+from __future__ import annotations
+
+import random
+import time
+
+from .config import FrameConfig
+
+QUEUE_TARGET_LEN = 10
+
+
+def _top_up(cfg: FrameConfig, assets: list[dict]) -> None:
+    valid_ids = {a["id"] for a in assets}
+    cfg.queue = [asset_id for asset_id in cfg.queue if asset_id in valid_ids]
+
+    needed = QUEUE_TARGET_LEN - len(cfg.queue)
+    if needed <= 0 or not assets:
+        return
+
+    excluded = set(cfg.queue)
+    if cfg.current_asset_id:
+        excluded.add(cfg.current_asset_id)
+
+    if cfg.order == "shuffle":
+        candidates = [a["id"] for a in assets if a["id"] not in excluded]
+        cfg.queue.extend(random.sample(candidates, min(needed, len(candidates))))
+        return
+
+    # Sequential: walk the album starting at queue_cursor, at most one full
+    # pass, wrapping around. queue_cursor resumes right after wherever this
+    # pass stopped, whether or not it filled the queue (e.g. a small album
+    # where everything's already queued/current -- next call is then a
+    # cheap no-op scan until something's consumed).
+    n = len(assets)
+    cfg.queue_cursor %= n
+    added = 0
+    i = 0
+    for i in range(n):
+        if added >= needed:
+            break
+        asset_id = assets[(cfg.queue_cursor + i) % n]["id"]
+        if asset_id not in excluded:
+            cfg.queue.append(asset_id)
+            excluded.add(asset_id)
+            added += 1
+    cfg.queue_cursor = (cfg.queue_cursor + i + 1) % n
+
+
+def advance_forced(cfg: FrameConfig, assets: list[dict]) -> None:
+    """Unconditionally moves to the next photo, ignoring elapsed time, and
+    resets the interval clock from now. Used only by the explicit
+    next-photo action (POST /frame/advance) -- always mutates cfg."""
+    _top_up(cfg, assets)
+    if cfg.queue:
+        cfg.current_asset_id = cfg.queue.pop(0)
+    elif assets:
+        # Queue still empty after top-up (e.g. a single-photo album whose
+        # only asset is already current) -- keep showing what we have.
+        cfg.current_asset_id = assets[0]["id"]
+    cfg.current_asset_set_at = time.time()
+    # Refill back up to QUEUE_TARGET_LEN now that current_asset_id has
+    # changed -- otherwise the queue is left one short until the *next*
+    # advance, since the pop above consumes one of the items _top_up just
+    # added.
+    _top_up(cfg, assets)
+
+
+def get_current(cfg: FrameConfig, assets: list[dict]) -> bool:
+    """Time-based, idempotent path used by GET /frame/image. Advances only
+    if the current photo is unset/invalid or refresh_interval_s has
+    elapsed since it was set. Returns whether it changed anything, so the
+    caller knows whether to persist. Calling this repeatedly well within
+    the interval is a no-op both times -- what makes an unplanned device
+    reboot safe: it just re-reads the current photo instead of skipping
+    ahead, while a wake that lands after the interval has elapsed still
+    advances exactly once, even after a long time offline."""
+    valid_ids = {a["id"] for a in assets}
+    stale = (
+        not cfg.current_asset_id
+        or cfg.current_asset_id not in valid_ids
+        or (time.time() - cfg.current_asset_set_at) >= cfg.refresh_interval_s
+    )
+    if not stale:
+        return False
+    advance_forced(cfg, assets)
+    return True

server/app/templates/index.html

@@ -22,6 +22,14 @@
     .info-box { margin-top: 16px; padding: 10px; border-radius: 4px; font-size: 13px; background: #f3f4f6; color: #444; }
     .info-box.warn { background: #fef9c3; color: #854d0e; }
     code { background: #f3f4f6; padding: 2px 5px; border-radius: 3px; }
+    h2.section { font-size: 16px; margin-top: 28px; margin-bottom: 8px; }
+    .thumb { width: 160px; max-width: 100%; border-radius: 4px; display: block; }
+    #upcoming-list { list-style: none; padding: 0; margin: 0; }
+    .queue-item { display: flex; align-items: center; gap: 10px; padding: 6px 0; border-bottom: 1px solid #eee; }
+    .queue-item img { width: 48px; height: 48px; object-fit: cover; border-radius: 4px; }
+    .queue-item .spacer { flex: 1; }
+    .queue-item button { margin: 0; padding: 4px 10px; font-size: 13px; background: #6b7280; }
+    .queue-item button:disabled { opacity: 0.35; cursor: default; }
   </style>
 </head>
 <body>
@@ -63,6 +71,12 @@
   </form>
   <div id="result"></div>
 
+  <h2 class="section">Now displaying</h2>
+  <div id="current-thumb"><p class="sub">Loading...</p></div>
+
+  <h2 class="section">Upcoming</h2>
+  <ul id="upcoming-list"></ul>
+
   <script>
     const resultEl = document.getElementById('result');
 
@@ -117,10 +131,91 @@
       try {
         await saveConfig();
         showStatus(true, 'Saved.');
+        loadQueue();
       } catch (e) {
         showStatus(false, e.message);
       }
     });
+
+    let upcomingItems = [];
+
+    function renderUpcoming(items) {
+      upcomingItems = items;
+      const list = document.getElementById('upcoming-list');
+      list.innerHTML = '';
+      items.forEach((item, i) => {
+        const li = document.createElement('li');
+        li.className = 'queue-item';
+
+        const img = document.createElement('img');
+        img.src = item.thumbnail_url;
+        li.appendChild(img);
+
+        const spacer = document.createElement('span');
+        spacer.className = 'spacer';
+        li.appendChild(spacer);
+
+        const upBtn = document.createElement('button');
+        upBtn.type = 'button';
+        upBtn.textContent = '↑';
+        upBtn.disabled = i === 0;
+        upBtn.addEventListener('click', () => moveItem(i, -1));
+        li.appendChild(upBtn);
+
+        const downBtn = document.createElement('button');
+        downBtn.type = 'button';
+        downBtn.textContent = '↓';
+        downBtn.disabled = i === items.length - 1;
+        downBtn.addEventListener('click', () => moveItem(i, 1));
+        li.appendChild(downBtn);
+
+        list.appendChild(li);
+      });
+    }
+
+    async function moveItem(index, delta) {
+      const newIndex = index + delta;
+      if (newIndex < 0 || newIndex >= upcomingItems.length) {
+        return;
+      }
+      const items = upcomingItems.slice();
+      [items[index], items[newIndex]] = [items[newIndex], items[index]];
+      renderUpcoming(items);
+      try {
+        const resp = await fetch('/api/queue/reorder', {
+          method: 'POST',
+          headers: { 'Content-Type': 'application/json' },
+          body: JSON.stringify({ queue: items.map((item) => item.id) }),
+        });
+        if (!resp.ok) {
+          throw new Error(await resp.text());
+        }
+      } catch (e) {
+        showStatus(false, e.message);
+        loadQueue();
+      }
+    }
+
+    async function loadQueue() {
+      const currentEl = document.getElementById('current-thumb');
+      try {
+        const resp = await fetch('/api/queue');
+        if (!resp.ok) {
+          currentEl.innerHTML = '<p class="sub">Not available yet -- configure Immich and an album first.</p>';
+          renderUpcoming([]);
+          return;
+        }
+        const data = await resp.json();
+        currentEl.innerHTML = data.current
+          ? `<img class="thumb" src="${data.current.thumbnail_url}">`
+          : '<p class="sub">Nothing displayed yet.</p>';
+        renderUpcoming(data.upcoming);
+      } catch (e) {
+        currentEl.innerHTML = '<p class="sub">Could not load.</p>';
+      }
+    }
+
+    loadQueue();
   </script>
 </body>
 </html>