Next/back button assignment moves from a frame-level "Button
assignments" card into each widget's own gear-icon dialog, prefilled
with a sane default at creation (photos/calendar -> advance/back,
whiteboard/weather -> check_now, others -> none). At most one binding
per (widget, button) now -- cross-widget execution order never
mattered since each widget's action only touches its own state.
New firmware capability: holding NEXT or BACK past a configurable
duration (min 3s, server-side default) triggers a frame-wide action
instead of the per-widget short-press one -- cycling saved layouts,
refreshing all widgets, or freezing/unfreezing every photo widget (see
app/global_actions.py). Firmware next/back checks gain the same
hold-duration polling the combo button already had; the threshold
comes from the previous wake's /frame/config fetch (persisted in NVS),
since this wake's button decision happens before that request.
Not done here: firmware/version.txt is intentionally left unbumped --
this hasn't been built or hardware-tested (no ESP-IDF toolchain in this
environment), so no firmware release build should be triggered yet.
battery_read_percent() was called once at the very start of boot, before
WiFi even connects, and that value was reused both for the manage-menu
overlay and the server report. Taken right after a reset (e.g. the OTA
reboot that immediately precedes it), the rail may still be settling --
plausible source of noisy jumps in reported battery level.
Now there's a single read, in frame_client_run() right before
report_battery(), after the photo (and manage overlay, if shown) is
already on the panel -- the fetch/display work already done this cycle
is the settle time, no delay to guess. The manage overlay no longer
needs an early local reading at all: it shows the server's last-known
value instead, added to the /frame/photo-info response it already
fetches.
Battery (firmware + server, disabled by default): new battery.c reads
a 2x200k voltage divider via ADC oneshot with curve-fitting calibration
(the ESP32-C6's scheme), maps through a piecewise LiPo discharge curve,
and restores the pin to button duty after each read -- the settled
XIAO ESP32-C6 design shares the back button's GPIO0/A0, time-shared per
wake. Skipped entirely when on mains (a 2x100k VBUS divider into a
spare digital pin -- the 5V pin is dead on battery power, so presence =
mains, where the charging voltage would read misleadingly full) or when
the reading is implausible. The manage overlay gains a battery region
(static outline glyph + "NN%", below the manage QR, all menu levels),
and the device POSTs to the new /frame/battery endpoint after a
successful fetch; the server stores percent + as-of timestamp, exposed
via /api/queue and shown in the web UI. FRAME_BATTERY_ADC_GPIO /
FRAME_VBUS_SENSE_GPIO default to -1 (fully inert on the dev board);
compile-verified both disabled and enabled, hardware bring-up deferred
until the ordered XIAO + batteries arrive.
Orientation (server-side only): new config setting + web UI dropdown
(landscape / portrait / landscape_flipped / portrait_flipped). Photos
are composed/cropped at the logical hanging shape (portrait crops at
480x800, so face-aware crops match how the frame actually hangs), then
rotated losslessly into the panel's native 800x480 byte layout after
dithering -- the device never knows. Face-label anchors are transformed
through the same rotation (logical_to_native()) so they stay attached
to faces on rotated frames. Known documented limitation: the on-device
manage overlay still renders in native orientation, so it appears
sideways on a portrait-hung frame (QRs scan at any rotation; text reads
sideways).
Back button (new GPIO0, POST /frame/back): the server now tracks a
bounded history of previously-current photos (photo_queue.py), pushed
to on every advance (auto or forced) and popped by back_forced() --
symmetric with advance, so pressing next afterwards returns to right
where you were. frame_client.c's force_advance bool becomes a 3-way
fetch_action_t (NORMAL/ADVANCE/BACK) threaded through the whole fetch
path.
Also folds the separate reset and manage buttons onto one pin
(combo_button.c, replacing reset_button.c/manage_button.c entirely),
disambiguated by hold duration: quick press shows the management menu
(unchanged), ~3s hold-then-release soft-resets (esp_restart(), config
kept -- new), ~15s hold factory-resets (today's old reset behavior,
extended from 10s for clearer tier separation). Driven by a production
board (Seeed XIAO ESP32-C6) exposing only 3 of the ESP32-C6's 8
deep-sleep-wakeup-capable GPIOs -- next/back keep their own dedicated
pins where instant response matters most, everything else shares the
third pin via timing instead of needing its own. Same three-pin layout
now works on both the dev board and the production board.
Fixed a fast-tap bug in combo_button_check() before shipping: it only
did a live gpio_get_level() read to decide whether the button was
pressed at all, so a press fast enough to already be released by the
time boot reached that check was missed entirely (treated as "never
pressed" rather than "quick press"). Added the same latched
esp_sleep_get_gpio_wakeup_status() check the other buttons already use
for exactly this reason.
Pressing the manage button (GPIO1) overlays a small QR code -- "SCAN TO
MANAGE" -- in the top-right corner of whatever photo is currently on
screen, linking to the server's config page, then reverts to the plain
photo after 30 seconds.
The overlay is spliced into the existing streaming fetch as chunks pass
through (frame_client.c's http_read_fn), rather than buffering the full
192,000-byte frame in RAM: only the small overlay rectangle itself
(~30KB) is ever held in memory, generated via new stride-parameterized
drawing helpers (epd_draw_*_ex in epd_draw.c) that let the existing
QR/text drawing code target an arbitrarily-sized buffer instead of a
full-frame one. epd7in3e.c is untouched -- it has no idea an overlay
exists.
Factory-reset (GPIO3, hold 10s): clears stored WiFi/server config and
restarts into provisioning -- the deliberate, USB-free replacement for
the earlier reverted RST-based auto-reprovisioning idea.
Next-photo (GPIO2, tap): wakes the device and forces the server to
advance immediately via a new POST /frame/advance, instead of waiting
for the refresh interval. Both buttons arm themselves as deep-sleep GPIO
wakeup sources so a press is noticed promptly even while asleep.
Also makes GET /frame/image side-effect-free: it now only advances once
refresh_interval_s has elapsed since the current photo was set (tracked
server-side), so a device reboot for any reason just redisplays the
current photo instead of silently skipping ahead. The server maintains a
small reorderable upcoming-photos queue, viewable and rearrangeable from
the web UI.
RST/power-on trigger: checks esp_reset_reason() at the very top of boot.
ESP32-C6 can't electrically distinguish the RST/EN button from a genuine
power-on (both report ESP_RST_POWERON -- confirmed against ESP-IDF's own
docs, ESP_RST_EXT is explicitly "not applicable"), so POWERON is treated
as "user wants to reconfigure" and routes straight to provisioning. Safe
because the device's only normal restart path is ESP_RST_DEEPSLEEP (its
own scheduled wake), and crash-type resets (brownout/watchdog/panic)
report their own distinct reasons, not POWERON -- so a flaky power supply
or transient crash won't get bounced into provisioning, only an actual
power cycle or RST press will (which plausibly means the frame is being
moved/redeployed anyway).
Auto-fallback: a new NVS-persisted consecutive-failure counter
(frame_config_record_server_failure/reset_server_failures) tracks wakes
where the tools server was unreachable. After
CONFIG_FRAME_REPROVISION_AFTER_FAILURES in a row (default 12, ~1hr at the
retry interval), the device clears its stored WiFi config and
esp_restart()s rather than calling wifi_provisioning_start() directly --
doing that inline would mean initializing the display driver a second
time in the same session (frame_client_run already did once), the same
class of double-init bug hit earlier with WiFi. The next boot's
frame_config_load() naturally reports "not provisioned" and routes
through the existing, already-tested provisioning path with a single
fresh epd_init(). Solves the "I moved the server to a new address" case
without needing USB access.
Both frame_config_save() (fresh provisioning) and any successful server
contact reset the failure counter.
Splits provisioning (softAP + captive portal + NVS-backed config) into
wifi_provisioning.c and home-network connection into frame_client.c.
/save_config now parses the form body and persists it to NVS; on boot the
device goes straight to STA mode if a config exists, retrying a few times
before falling back to provisioning if the home network is unreachable.
The provisioning AP is now always named ESPRESSO with a random per-device
password (generated once, persisted in NVS) instead of a fixed Kconfig
value, drawn from a charset that avoids visually ambiguous characters since
it'll be read off the e-ink panel and possibly typed by hand.
Moves the existing ESP-IDF captive_portal example into firmware/ to make
room for the new FastAPI server and project docs, ahead of building out the
full ESPresso Frame project (ESP32-C6 + Immich-backed e-ink photo frame).
tfaour