After a successful home WiFi connect, frame_client_run() now redraws the
panel as a two-row checklist (WiFi row with a checkmark, server row) so
the connection sequence is visible on-device rather than only in serial
logs. Refreshes once with the server row pending, probes the tools server
with a plain HTTP HEAD (any response, even 404, confirms the socket-level
connection works -- there's no real server yet), then refreshes again with
the final result. Two refreshes rather than one to actually show staged
progress, at the cost of the extra refresh time inherent to this panel.
Also fixes a second hardware-verified bug in the same area: on a failed
STA connect falling back to provisioning, wifi_init_softap()'s
esp_wifi_init() call was aborting with ESP_ERR_INVALID_STATE, because
frame_wifi_connect_sta() only stopped the WiFi driver on failure rather
than fully deinitializing it (and destroying the STA netif) before
handing back control.
Adds a "2. CONFIGURATION" step alongside WiFi setup: a second QR code
linking straight to the captive portal page (http://<ap-ip>/), for anyone
who's joined the AP but wants a one-scan shortcut to the config form
instead of relying on the captive-portal popup. The AP netif is now
created (but not started) before the display renders, since the AP's IP
is fixed at netif creation and needed for this QR before the network is
actually up.
Pulls the pixel/text drawing primitives (previously private to
qr_onboarding.c) out into epd_draw.c/.h so the upcoming status screen can
reuse them instead of duplicating.
Two crashes found flashing to real hardware:
- epd_display_stream's 4KB SPI chunk buffer was a stack local, but the
default main task stack (3584 bytes) is smaller than that alone --
Guru Meditation stack protection fault. Made it static instead, and
bumped CONFIG_ESP_MAIN_TASK_STACK_SIZE to 8192 for headroom in the rest
of the boot call chain (provisioning -> QR render -> eventually the
HTTP fetch cycle all run in this one task).
- epd_wait_busy() polled with a 1ms vTaskDelay, which rounds down to 0
FreeRTOS ticks at the default 100Hz tick rate -- so it never actually
blocked, tight-spinning the CPU for the panel's real refresh time
(15-30+s for a full-color pass) and starving the idle task long enough
to trip the 5s task watchdog. Bumped to 20ms, safely >=1 tick regardless
of tick rate.
Also updates the EPD pin defaults to the board's actual wiring
(CLK=20 MOSI=19 CS=18 DC=9 RST=10 BUSY=11), confirmed working on hardware.
Vendors two small MIT/BSD-3-Clause libraries rather than hand-rolling
either: Nayuki's qrcodegen (QR matrix generation) and Waveshare's Font24
bitmap table from their e-Paper repo (same repo the epd7in3e driver came
from) for rendering readable text on the panel.
qr_onboarding_show() builds a standard WIFI:T:WPA;S:...;P:...;; payload,
rasterizes the QR module matrix plus the SSID and password as plaintext
underneath (for anyone provisioning from a device that can't scan a QR)
onto a malloc'd frame buffer, and pushes it to the panel via
epd_display_buffer(). The buffer is heap-allocated on demand rather than
statically reserved, since 192KB held permanently in BSS would eat into
the RAM budget the HTTP fetch path (task 6) is specifically trying to keep
free.
Wired into wifi_provisioning_start() before the softAP comes up, so the
join instructions are already on-screen by the time the network is
joinable.
The board's flash is 8MB, but neither flash size nor partition table were
pinned in sdkconfig.defaults, so a fresh clone would silently fall back to
IDF's default (2MB flash, ~1MB "single app" partition table) rather than
what this project was actually being built/tested against. Building against
that default left only 4% of the app partition free before the HTTP client
work (task 6) even lands. Adds a custom partitions.csv with a 2MB app
partition and pins CONFIG_ESPTOOLPY_FLASHSIZE_8MB so the committed config
reproduces a working build for anyone else who clones this.
Ports Waveshare's official EPD_7in3e.c register/refresh sequence (the
panel has no public datasheet, so their reference driver is the source of
truth) to an ESP-IDF component using spi_master + gpio instead of the
bcm2835/RPi hardware abstraction the reference targets.
Unlike the reference driver, which toggles CS around every single byte,
this holds CS low for each logical command/data phase and DMAs pixel data
in 4KB chunks -- sending ~192,000 individual one-byte SPI transactions
would make a full refresh impractically slow.
Exposes a streaming API (epd_display_stream, pulling chunks from a
caller-supplied read_fn) so the eventual HTTP fetch path can feed the panel
without holding a full ~192KB frame in RAM, plus an in-memory convenience
wrapper (epd_display_buffer) for cases like the upcoming QR code screen
where buffering the whole frame is fine.
Wired into wifi_provisioning_start() as an init + white-clear for now, to
prove the driver builds/links/runs at the right point in the boot sequence
ahead of the actual QR code content.
Two frames on the same network would otherwise both advertise the same
ESPRESSO SSID during provisioning. Appends the last 3 bytes of the WiFi MAC
(read via esp_read_mac(), available before the WiFi driver starts) so each
device's softAP is uniquely named.
Splits provisioning (softAP + captive portal + NVS-backed config) into
wifi_provisioning.c and home-network connection into frame_client.c.
/save_config now parses the form body and persists it to NVS; on boot the
device goes straight to STA mode if a config exists, retrying a few times
before falling back to provisioning if the home network is unreachable.
The provisioning AP is now always named ESPRESSO with a random per-device
password (generated once, persisted in NVS) instead of a fixed Kconfig
value, drawn from a charset that avoids visually ambiguous characters since
it'll be read off the e-ink panel and possibly typed by hand.
Moves the existing ESP-IDF captive_portal example into firmware/ to make
room for the new FastAPI server and project docs, ahead of building out the
full ESPresso Frame project (ESP32-C6 + Immich-backed e-ink photo frame).
tfaour