espresso_frame/firmware/README.md

# ESPresso Frame Firmware

ESP-IDF firmware for the ESP32-C6. On first boot it provisions itself over
a WiFi captive portal; after that it wakes on a timer, fetches an
already-processed frame from the [server](../server/), streams it straight
to the panel over SPI, and goes back to deep sleep.

See [`docs/architecture.md`](../docs/architecture.md) for the full boot/fetch
cycle and [`docs/hardware.md`](../docs/hardware.md) for wiring.

## Build and flash

Requires [ESP-IDF](https://docs.espressif.com/projects/esp-idf/en/stable/esp32c6/get-started/)
(developed against v5.x/v6.x) with the environment sourced (`. $IDF_PATH/export.sh`
or your distro's equivalent).

```
idf.py set-target esp32c6
idf.py build
idf.py -p PORT flash monitor
```

(`Ctrl-]` exits the monitor.)

The committed [`sdkconfig.defaults`](sdkconfig.defaults) pins an 8MB flash
size and a custom [`partitions.csv`](partitions.csv) (2MB app partition --
the default "single app" ~1MB partition runs out of room once the HTTP
client, TLS, and vendored fonts/QR library are linked in). If your board
has less flash, you'll need to shrink the app partition and drop features
to fit.

## Configuration (`idf.py menuconfig`)

Under **ESPresso Frame Configuration**:

| Option | Default | What it does |
| --- | --- | --- |
| `ESP_AP_SSID` | `ESPRESSO` | Provisioning softAP SSID prefix (device appends `_XXXXXX` from its MAC) |
| `ESP_MAX_STA_CONN` | 4 | Max clients on the provisioning softAP |
| `ESP_ENABLE_DHCP_CAPTIVEPORTAL` | on | DHCP Option 114 captive portal detection |
| `FRAME_STA_CONNECT_MAX_RETRIES` | 3 | Home WiFi connect attempts before falling back to provisioning |
| `FRAME_STA_CONNECT_TIMEOUT_MS` | 15000 | Per-attempt WiFi connect timeout |
| `FRAME_SERVER_CHECK_TIMEOUT_MS` | 3000 | Timeout for `GET /frame/config` (reachability check + refresh interval) |
| `FRAME_FETCH_TIMEOUT_MS` | 15000 | Timeout for `GET /frame/image` |
| `FRAME_SLEEP_INTERVAL_S` | 3600 | **Fallback only** -- the refresh interval is normally set server-side; see below |
| `FRAME_RETRY_INTERVAL_S` | 300 | Sleep duration after a failed cycle, before retrying |
| `FRAME_NEXT_BUTTON_GPIO` | 2 | Next-photo button GPIO (-1 to disable). Must be 0-7 (ESP32-C6's deep-sleep-wakeup-capable pins) |
| `FRAME_BACK_BUTTON_GPIO` | 0 | Back-photo button GPIO (-1 to disable). Must be 0-7 |
| `FRAME_COMBO_BUTTON_GPIO` | 1 | Menu/reset button GPIO (-1 to disable). Must be 0-7 |
| `FRAME_COMBO_SOFT_RESET_HOLD_MS` | 3000 | How long the combo button must be held (then released) to soft-reset |
| `FRAME_COMBO_FACTORY_RESET_HOLD_MS` | 15000 | How long the combo button must be held to factory-reset |
| `FRAME_BATTERY_ADC_GPIO` | -1 (disabled) | Battery voltage-divider ADC GPIO; see the Battery section below |
| `FRAME_VBUS_SENSE_GPIO` | -1 (disabled) | USB-power sense GPIO for hiding the battery indicator on mains |

Under **E-Paper Display (epd7in3e) Configuration**: SPI/GPIO pin
assignments and SPI clock speed -- see
[`docs/hardware.md`](../docs/hardware.md) for the wiring these correspond to.

### Why `FRAME_SLEEP_INTERVAL_S` says "fallback"

The actual refresh interval is set from the server's web UI (see
[`server/README.md`](../server/README.md)) and delivered to the device on
every wake via `GET /frame/config`, so it can be changed without
reflashing. The Kconfig value only applies before the device has ever
successfully reached a configured server, or if the response doesn't
include a valid interval.

## First boot

With no stored WiFi config (a fresh device, or after erasing NVS -- see
below), the device brings up the display before anything else and shows a
two-step setup screen:

1. **Connect to WiFi** -- a QR code encoding `WIFI:T:WPA;S:...;P:...;;`
   for the device's own `ESPRESSO_XXXXXX` softAP, with the SSID and
   password also printed underneath for anyone provisioning from a
   desktop/laptop that can't scan a QR code.
2. **Configure device** -- a QR code linking straight to the captive
   portal's config page (`http://192.168.4.1/` by default), for a
   one-scan shortcut once you've joined the AP.

The config page asks for your home WiFi SSID/password, the "Tools
Server" address (`host:port` of the [server](../server/) -- **not** your
Immich server; see below for the `https://` form), and an optional
"Access Token" (see below). Saving reboots the device, which then
connects to your home network and starts its normal fetch/sleep cycle.

## HTTP vs HTTPS

The Tools Server field accepts either:

- `host:port` (e.g. `192.168.1.50:8420`) -- plain HTTP, talks straight to
  the [server](../server/), which never speaks TLS itself. This is the
  default and needs nothing extra.
- `https://host[:port]` (e.g. `https://frame.example.com`) -- HTTPS,
  for a TLS-terminating reverse proxy (nginx, etc.) sitting in front of
  the server. Every URL the device builds (image fetch, config check,
  manage-menu overlay data, the QR codes' own links) uses whichever
  scheme you enter.

The firmware trusts ESP-IDF's standard public CA bundle
(`esp_crt_bundle_attach`) -- so any reverse proxy with a normal
publicly-trusted certificate just works out of the box: Let's Encrypt,
a Cloudflare-proxied hostname, or any other public CA.

One specific root is added on top of that bundle at build time, from
[`main/certs/additional_root_ca.pem`](main/certs/additional_root_ca.pem)
(wired in via `CONFIG_MBEDTLS_CUSTOM_CERTIFICATE_BUNDLE_PATH` in
[`sdkconfig.defaults`](sdkconfig.defaults)): **GlobalSign Root CA R1**.
This isn't a workaround specific to one deployment -- it's needed
because Cloudflare (via Google Trust Services) commonly cross-signs its
GTS Root R4 chain with this old GlobalSign root for backward
compatibility with older/embedded clients, and ESP-IDF's current bundle
snapshot has removed it (deprecated from modern trust stores). Without
it, ESP-IDF's chain validation -- which looks up a trusted root by the
*issuer name* of whatever certificate it can't otherwise validate, not
by matching the presented certificate itself -- comes up empty and the
handshake fails with "No matching trusted root certificate found",
confirmed on hardware against a real Cloudflare-fronted deployment.
Since this is a common, not deployment-specific, gap, it's likely worth
keeping even if you're not using Cloudflare.

If your proxy presents a certificate chain the bundle (plus this one
addition) still doesn't validate -- an unusual public CA, or a private/
self-signed cert with no public CA in the chain at all -- diagnose with:

```
openssl s_client -connect <host>:443 -showcerts </dev/null
```

and add whichever certificate in the chain is missing to
`additional_root_ca.pem` (or a file of your own, if you'd rather not
touch the committed one) alongside the existing entry, then rebuild.

The device does perform normal hostname verification (it's not
skipped), so the Tools Server field's hostname has to match what the
certificate was actually issued for -- a bare LAN IP address
(`https://192.168.1.50`) will fail the handshake even against a
perfectly valid cert for a different name.

## Access token

If the server has `MANAGEMENT_TOKEN` set (see
[`server/README.md`](../server/README.md)), it requires that same value
on every request -- the web UI *and* every device-facing request the
frame itself makes. Paste it into the captive portal's "Access Token"
field and the device sends it (`?token=...`) on every request
automatically, and bakes it into the manage-menu/share QR codes so
scanning them just works too. Leave it blank if the server has no
`MANAGEMENT_TOKEN` configured -- the default, unauthenticated-on-a-
trusted-LAN behavior from before.

## Skipping to the next photo

Wire a momentary push button between GPIO2 and GND (internal pull-up,
active-low, same wiring style as the other buttons). A press wakes the
device (if asleep) and tells the server to advance to the next photo
right away, regardless of the configured refresh interval -- no long hold
needed, since advancing is easily reversible by pressing again. See
`FRAME_NEXT_BUTTON_GPIO` above to change the pin or disable the feature.

Normal wakes and reboots never advance the photo on their own -- the
server decides when to advance based on its own clock (see
[`server/README.md`](../server/README.md)), so an unplanned reboot just
redisplays whatever was already showing instead of skipping ahead.

## Going back to the previous photo

Wire a momentary push button between GPIO0 and GND (same wiring style as
the other buttons). A press wakes the device (if asleep) and tells the
server to return to whichever photo was showing immediately before the
current one, regardless of whether it got there by the normal timer or
the next-photo button. Pressing next afterwards returns to where you
were before pressing back -- it's a real undo, not a separate "recently
shown" list. See `FRAME_BACK_BUTTON_GPIO` above to change the pin or
disable the feature.

If there's nothing to go back to yet (freshly provisioned, or you've
already gone back as far as there is history), it's a no-op -- the
current photo stays exactly as it was, no flash on the panel.

## Battery (XIAO ESP32-C6)

Disabled by default (`FRAME_BATTERY_ADC_GPIO = -1`) -- correct for a
dev board with no battery wired. On the intended production board (Seeed
XIAO ESP32-C6) with a 1S LiPo:

**Wiring** (beyond soldering the battery itself to the BAT+/BAT- pads on
the XIAO's underside -- note the polarity markings there, and that
JST-PH battery connector polarity is *not* standardized, so verify with
a multimeter before first plug-in):

- **Battery sense**: a 2x200k voltage divider from BAT+ to GND, midpoint
  into an ADC-capable pin (GPIO 0-6; the settled design shares the back
  button's GPIO0/A0 -- the high-impedance divider coexists fine with the
  button, and firmware time-shares the pin with a brief ADC read once
  per wake). Set `FRAME_BATTERY_ADC_GPIO` to match.
- **Mains detection** (optional): a 2x100k divider from the 5V pin
  (which only carries voltage when USB is plugged in) into any spare
  GPIO -- plain digital high/low, no ADC needed. The divider is
  required: raw 5V exceeds the 3.3V pin limit. Set
  `FRAME_VBUS_SENSE_GPIO`.

**Behavior**: once per wake the firmware reads the battery voltage,
converts it to a percent via a LiPo discharge curve, shows it (battery
icon + "NN%") below the "scan to manage" QR box whenever the management
menu is up, and reports it to the server (`POST /frame/battery`), which
displays it in the web UI with an "as of" timestamp. All of that is
skipped when on mains power (the charging voltage would read
misleadingly full), when the reading is implausible (no battery
attached), or when the feature is disabled.

## Managing the queue, soft-resetting, and factory-resetting

One more button, wired between GPIO1 and GND (same wiring style as the
other buttons), covers three actions -- disambiguated purely by how
long it's held:

**A quick press** wakes the device and overlays several corners of
whatever photo is currently showing, leaving the middle of the photo
visible and unchanged:

- **Top-right**: a QR code -- "SCAN TO MANAGE" -- linking to the
  server's config page.
- **Top-left**: the photo's location, if Immich reverse-geocoded it from
  GPS EXIF (skipped entirely if not).
- **Bottom-right**: the date the photo was taken, if known.
- **Bottom-left**: a QR code linking to a public, view-only Immich share
  link for that exact photo. The link is only created once someone
  actually scans it, and expires 30 minutes after that.

After 30 seconds with no further presses it automatically reverts to the
plain photo. Pressing the button *again* while this is up escalates to a
second menu level -- everything above, plus the name of anyone Immich
has identified labeled right next to their face in the photo (skipped
for faces Immich hasn't been told a name for; no face detection happens
on the device or the server, this is entirely Immich's own People
feature). A third press exits immediately rather than waiting out the
30-second timer. Holding the button during this stage doesn't trigger
either reset tier below -- the hold-duration read only ever happens
once, right when the device first wakes, before any menu is shown.

The device stays awake for the whole menu interaction (up to three
physical refreshes: the base overlay, the escalated one, and
reverting), so this costs meaningfully more power than a normal wake --
expected for a deliberate, occasional action, same tradeoff as the
other buttons.

**Holding it ~3 seconds, then releasing** soft-resets the device --
`esp_restart()`, keeping the stored WiFi/server config. Useful for
recovering a hung device without losing setup.

**Holding it ~15 seconds** (whether or not you're still holding it --
this fires immediately, it doesn't wait for release) clears the stored
WiFi/server config and restarts into provisioning. From either power-on
or while the device is deep-asleep, since this GPIO is armed as a
wakeup source.

See `FRAME_COMBO_BUTTON_GPIO`, `FRAME_COMBO_SOFT_RESET_HOLD_MS`, and
`FRAME_COMBO_FACTORY_RESET_HOLD_MS` above to change the pin or hold
durations, or disable all three actions.

Without the button wired up (or with `FRAME_COMBO_BUTTON_GPIO` set to
`-1`), reconfiguring still works by erasing the NVS partition over USB:

```
python -m esptool --chip esp32c6 -p PORT erase-region 0x9000 0x6000
```

(Offset/size match the `nvs` entry in [`partitions.csv`](partitions.csv);
this only wipes the config, not the app itself.)